If you want to, you can check how much good quality data the Alice NightOne device collected during your HSAT. You’ll have an appointment to return them. Bring the case, device, and sensors back to the Memorial Sloan Kettering (MSK) location where you picked them up. Put the Alice NightOne device and sensors back into the carrying case. To end your HSAT, take off the sensors and disconnect them from the Alice NightOne device. If any of the sensors slip off or move during the night, put them back on. Leave the Alice NightOne device and sensors on all night, even if you get up to use the restroom or for any other reason. You can sleep in your usual position (such as on your back, side, or stomach) during your HSAT. Once all the icons have turned off, the Alice NightOne device is ready. After about a minute, the icons will start to turn off one by one. Once all the sensors are connected and working properly, the 3 sensor icons and the good study indicator will be solid green. Then, take a few more breaths and check the icon again. If it doesn’t, check the position of the sensor. The pulse oximeter icon should turn green. Take several breaths with the pulse oximeter in place.Place the sensor so the wire goes over the back of your hand.If you have a fake nail or are wearing nail polish, remove this before putting the pulse oximeter on. The pulse oximeter only works on a natural, clean nail. Put the rubber sensor on one of your index (pointer) fingers (see Figure 8). The belt should be snug but not too tight.įigure 8. The effort belt should be evenly across your nipples or above your breasts. Wrap the effort belt around your chest so the Alice NightOne device is in the center of your chest (see Figure 3).Put them on while you’re standing or sitting up, not lying down. Once you’re ready for bed, put the sensors on as directed below. Wear a loose-fitting top (such as a t-shirt) on the night of your HSAT. Use the instructions in this section to help remember how to put on the sensors at home. They will also adjust the effort belt for you. Your healthcare provider will show you how to put on the sensors. For more information about this, read the section “Checking the data quality” near the end of this resource. You can do this in the morning to check how much good quality data was collected. End your HSAT and show the good study indicator.You can do this during your HSAT to check if the sensors are connected and working properly. If you want, you can use the user button to: You don’t need to use it during your HSAT if you don’t want to. The user button is the round button on the front of the Alice NightOne device. The 4 parts of the good study indicator can light up separately. It also tells you when the Alice NightOne device is turning on or off. The good study indicator (see Figure 2) can tell you how how much of the data from your HSAT is good quality. The top of the Alice NightOne device has 4 icons that light up to give you information. Don’t get the Alice NightOne device or sensors wet. Follow the safety instructions in the user manual. The case will also have a user manual and quick start guide. You will only use these if the batteries inside the Alice NightOne device stop working. The pulse oximeter should already be attached to the Alice NightOne device. It will measure your pulse, blood flow, and the amount of oxygen in your blood. This is a wire with a gray rubber sensor that you’ll place on your finger. It will measure how much air you’re breathing and keep track of your snoring. This is a thin, flexible tube that you’ll place under your nose. One end of the effort belt should already be attached to the Alice NightOne device. It will measure how hard your lungs are working. This is a belt you’ll wear around your chest. It will also store all the information from your HSAT. This is a rectangular device that will keep track of your body position (information such as whether you’re lying on your back, side, or stomach). Your healthcare provider will give you a case with everything you need for your HSAT. Back to top About the Alice NightOne Device and Sensors Alice NightOne is a medical device with sensors that’s used to diagnose obstructive sleep apnea (OSA). This information explains how to use an Alice NightOne device for your home sleep apnea test (HSAT).
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |